liberato87 Posted May 17, 2012 Share Posted May 17, 2012 Grazie. I buchi ben puliti con lima e carta vetrata con la vista dall'interno stavolta: Non li ho fatti nemmeno troppo precisi, tanto vanno coperti dai passacavi Corsair si infatti avevo notato che nella prima foto erano da "limare" però poi con i gommini appunto non si vedeva niente quindi potevano restare benissimo così! mi pare davvero un ottimo lavoro compare! Quote Link to comment Share on other sites More sharing options...
Opmet Posted May 17, 2012 Author Share Posted May 17, 2012 sopra non ti servono fori per i cavi di alimentazione?? Ci sta, bello lungo. Nella prime due foto è la vista da dietro con case rovesciato, infatti il buco per la cpu sta sotto e se ci fai caso più giù c'è quel buco lunghissimo per far passare i cavi delle ventole e prolunga 8pin cpu, solo che serve un'altra "PICCOLA" modifica... si infatti avevo notato che nella prima foto erano da "limare" però poi con i gommini appunto non si vedeva niente quindi potevano restare benissimo così!mi pare davvero un ottimo lavoro compare! Grazie per i complimenti, fanno sempre piacere I buchi van sempre limati, più che altro c'è sempre il rischio che ti si infila qualche scheggia di metallo sottocute e poi sono dolori... Ah cmq il buco extra è quello alla fine del cestello per le unità da 5,25" L'ho fatto per far passare i cavi del rheobus, compreso l'attacco molex 4pin Quote Link to comment Share on other sites More sharing options...
Opmet Posted May 17, 2012 Author Share Posted May 17, 2012 Un altro piccolo accorgimento: Piccola modifica necessaria per permettere il passaggio della prolunga 8pin della cpu e nel frattempo riuscire a chiudere la paratia destra Quote Link to comment Share on other sites More sharing options...
Gianluca92 Posted May 17, 2012 Share Posted May 17, 2012 allora alla CM che ce l'hanno fatto a fa il buco? Quote Link to comment Share on other sites More sharing options...
Opmet Posted May 17, 2012 Author Share Posted May 17, 2012 allora alla CM che ce l'hanno fatto a fa il buco? Mah, tu lo sai? Forse per cavi di spessore più piccolo, ad esempio ventole ecc ecc... Senza quella modifica un cavo a 8pin cpu NON può passare da dietro Quote Link to comment Share on other sites More sharing options...
Gianluca92 Posted May 17, 2012 Share Posted May 17, 2012 dovrebbero assumere noi alla CM:asd: Quote Link to comment Share on other sites More sharing options...
liberato87 Posted May 17, 2012 Share Posted May 17, 2012 ahahah giulio infatti oggi quando ho visto quel foro squadrato in basso ho pensato che ero io che guardavo il case al contrario e che quello fosse il foro per permettere di smontare/montare il backplate senza smontare la main ahahahha Quote Link to comment Share on other sites More sharing options...
Opmet Posted May 17, 2012 Author Share Posted May 17, 2012 Questo povero case lo sto martoriando, poverino... :( Dove posso trovare un template per una griglia Phobya 360? Così magari faccio l'ultimo taglio ed inizio a verniciare prima che mi arriva la roba da Ybris? Quote Link to comment Share on other sites More sharing options...
tom1 Posted May 18, 2012 Share Posted May 18, 2012 ahahha in effetti ha ragione libe Quote Link to comment Share on other sites More sharing options...
Opmet Posted May 19, 2012 Author Share Posted May 19, 2012 Intanto una fotina della mia postazione "provvisoria": Una sistemazione veloce veloce, non avevo voglia di tagliare quel tubo lunghissimo Quote Link to comment Share on other sites More sharing options...
liberato87 Posted May 19, 2012 Share Posted May 19, 2012 e bravoooooooooooooo Quote Link to comment Share on other sites More sharing options...
tom1 Posted May 19, 2012 Share Posted May 19, 2012 complimenti giulio Quote Link to comment Share on other sites More sharing options...
Luka83 Posted May 19, 2012 Share Posted May 19, 2012 Bravo, vedo che hai già messo a lavoro i kit. Però là vedo solo una scheda, io ti ho inviato 2 kit....... Non fare il furbo e monta l'altra VGA Quote Link to comment Share on other sites More sharing options...
Opmet Posted May 19, 2012 Author Share Posted May 19, 2012 Certo che sto xspc rs360 per essere uno slim è davvero buono, mi tiene senza problemi (non sotto bench, non ho provato) il 2600k a 4500 e la 6950@70, giocando a black ops (una cagata ) temp massima cpu 52° e temp massima gpu 33°, con una tamb di circa 21°... Va benino dai Quote Link to comment Share on other sites More sharing options...
Opmet Posted May 19, 2012 Author Share Posted May 19, 2012 Bravo, vedo che hai già messo a lavoro i kit. Però là vedo solo una scheda, io ti ho inviato 2 kit....... Non fare il furbo e monta l'altra VGA Pagamento effettuato adesso. Grazie. In realtà ho 2 kit vr001, 2 wubbi vga, però una sola 6950... Mi piacerebbe prendere la seconda, però al momento non posso permettermela Vedremo più avanti, per ora una per giocare a 1920x1080 mi basta Quote Link to comment Share on other sites More sharing options...
tom1 Posted May 19, 2012 Share Posted May 19, 2012 giulio vedo che hai qualcosa di tosto in cantiere Quote Link to comment Share on other sites More sharing options...
Opmet Posted May 19, 2012 Author Share Posted May 19, 2012 giulio vedo che hai qualcosa di tosto in cantiere Cioè? Non mi risulta nulla di "grosso" in cantiere :S Quote Link to comment Share on other sites More sharing options...
tom1 Posted May 19, 2012 Share Posted May 19, 2012 vabbe per una seconda vga se è confermato dalle prolunghe che hai preso da luca Quote Link to comment Share on other sites More sharing options...
Opmet Posted May 19, 2012 Author Share Posted May 19, 2012 Da Luca ho preso 2 kit vr001 della arctic, il prezzo era buono e ne ho approfittato. Per la seconda vga ci devo pensare mooooolto a fondo, non credo valga ancora la pena fare uno cfx di 6950 moddate a 6970, bhò... Quote Link to comment Share on other sites More sharing options...
tom1 Posted May 19, 2012 Share Posted May 19, 2012 bhè per fare punticini e godersi qualche gioco meglio si Quote Link to comment Share on other sites More sharing options...
Opmet Posted May 20, 2012 Author Share Posted May 20, 2012 Ultimo taglio (da fare :() dopodichè lascio in pace questo povero case... Quote Link to comment Share on other sites More sharing options...
tom1 Posted May 20, 2012 Share Posted May 20, 2012 susu vediamo sto triventola Quote Link to comment Share on other sites More sharing options...
Opmet Posted May 20, 2012 Author Share Posted May 20, 2012 susu vediamo sto triventola I buchi sotto ci sono già, solo che voglio fare un taglio più... elegante, per accogliere meglio la griglia Quote Link to comment Share on other sites More sharing options...
tom1 Posted May 20, 2012 Share Posted May 20, 2012 direi necessario Quote Link to comment Share on other sites More sharing options...
Opmet Posted May 21, 2012 Author Share Posted May 21, 2012 Ecco il risultato: Ecco il povero case ridotto ad un cumulo di lamiere :( poverino Purtroppo causa un (temo serio) infortunio giocando a calciotto, la verniciatura ritarderà parecchio :( Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.