vjncenzo Posted August 21, 2010 Share Posted August 21, 2010 Salve a tutti. Avrei bisogno di alcune informazioni. Ho portato il mio processore a 3600MHz cambiando solo i seguenti parametri FSB Frequency 400 PCIE Frequency 101 DRAM Frequency 1066Mhz Oltre a questo ho impostato il vcore a 1.25V. Adesso non voglio aumentare la frequenza del processore, mi basta a 3.6, vorrei solo sapere se ci sono degli accorgimenti da fare. Le ram sono Corsair CM2X2048-8500C5D 1066MHz Panoramica del bios Yfrog Video : yfrog.com/61mov00008z Grazie Quote Link to comment Share on other sites More sharing options...
Le085 Posted August 21, 2010 Share Posted August 21, 2010 Benvenuto nel nostro forum :n2mu: Come impostazioni direi che vanno bene. Controlla la stabilità con prime95 in modalità blend fai un giro di linx e un 3dmark se non hai errori direi che sei a posto. Magari puoi provare a limare il vcore per vedere se riesci a stare in daily con un vcore più basso. Controlla anche le temp in full load:) Quote Link to comment Share on other sites More sharing options...
vjncenzo Posted August 21, 2010 Author Share Posted August 21, 2010 (edited) Ciao Le085. Ho fatto un test con Prime95 ed ecco i risultati idle full Adesso ho portato il vcore a 1.20V, impostato il CPU PLL a 1.58V e l'FSB Termination voltage a 1.24V. Vorrei trovare una configurazione stabile e che scaldi poco. Grazie. Edited August 21, 2010 by vjncenzo Quote Link to comment Share on other sites More sharing options...
Le085 Posted August 21, 2010 Share Posted August 21, 2010 dciamo che iniziano ad essere un po' altine.. sei col dissi stock? prova ad abbassare il vcore per vedere fin dove sei stabile... il vcore è difficile da determinare senza fare delle prove dimenticavo che per considerarti rock solid devi far girare prime95 per almeno due ore... e per sicurezza anche un giro di linx e un 3dmark06 non fanno certo male Quote Link to comment Share on other sites More sharing options...
vjncenzo Posted August 21, 2010 Author Share Posted August 21, 2010 Il dissipatore è un Noctua NH-C12P SE14 Adesso ho portato il vcore a 1.20V e sembra stabile. Non ho ancora fatto un test con Prime95, ma giocando non da problemi. I parametri CPU PLL a 1.58V e FSB Termination voltage a 1.24V secondo te possono andare? Domani faccio un test più approfondito. Grazie. Quote Link to comment Share on other sites More sharing options...
Le085 Posted August 22, 2010 Share Posted August 22, 2010 si direi di sì... se vuoi salire di più però bisogna iniziare ad aumentarli di uno step Quote Link to comment Share on other sites More sharing options...
vjncenzo Posted August 22, 2010 Author Share Posted August 22, 2010 A me bastano 3.6Ghz. Se quei parametri possono andar bene per quella frequenza li lascio così. Quote Link to comment Share on other sites More sharing options...
tom1 Posted August 22, 2010 Share Posted August 22, 2010 A me bastano 3.6Ghz. Se quei parametri possono andar bene per quella frequenza li lascio così. si potresti lasciare cosi senza muovere altro Quote Link to comment Share on other sites More sharing options...
vjncenzo Posted August 22, 2010 Author Share Posted August 22, 2010 Ok, grazie tom1 Stamattina ho fatto un test di due ore con Prime95 e i seguenti settaggi FSB Frequency 400 PCIE Frequency 101 DRAM Frequency 1066Mhz VCORE 1.19375V CPU PLL a 1.58V FSB Termination voltage a 1.24V Come vede ho abbassato ancora il vcore e non ha dato problemi, però a lungo andare, con un voltaggio così basso, si può ronivare il processore? Quote Link to comment Share on other sites More sharing options...
Le085 Posted August 22, 2010 Share Posted August 22, 2010 semmai il contrario non può che fargli bene oltretutto consumi anche meno Quote Link to comment Share on other sites More sharing options...
vjncenzo Posted August 22, 2010 Author Share Posted August 22, 2010 Grazie :n2mu: Adesso posso lasciare così o ci sono altri parametri che potrei modificare? Quote Link to comment Share on other sites More sharing options...
tom1 Posted August 22, 2010 Share Posted August 22, 2010 puoi fermarti anche cosi non avrai problemi Quote Link to comment Share on other sites More sharing options...
vjncenzo Posted August 22, 2010 Author Share Posted August 22, 2010 Al massimo, se possibile, vorrei diminuire ancora il consumo. Quote Link to comment Share on other sites More sharing options...
tom1 Posted August 22, 2010 Share Posted August 22, 2010 bhe in quel caso devi dare meno voltaggio in quanto più aumenti i voltaggi più ci sarà un assorbimento Quote Link to comment Share on other sites More sharing options...
vjncenzo Posted August 22, 2010 Author Share Posted August 22, 2010 Sempre ai tre parametri che ho modificato, oppure è possibile farlo anche su altri? Quote Link to comment Share on other sites More sharing options...
tom1 Posted August 22, 2010 Share Posted August 22, 2010 è possibile farlo anche su altri ma non so se migliori di molto comunque sui parametri s3 s4 Quote Link to comment Share on other sites More sharing options...
vjncenzo Posted August 22, 2010 Author Share Posted August 22, 2010 Scusa nel bios con che voce li trovo e secondo te a quanto li dovrei mettere? Quote Link to comment Share on other sites More sharing options...
tom1 Posted August 22, 2010 Share Posted August 22, 2010 che scheda madre hai? Quote Link to comment Share on other sites More sharing options...
vjncenzo Posted August 22, 2010 Author Share Posted August 22, 2010 Asus P5Q Quote Link to comment Share on other sites More sharing options...
tom1 Posted August 22, 2010 Share Posted August 22, 2010 al momento non ricordo come sia la voce nella P5Q posso solo dirti se trovi una voce con C1E enabled Quote Link to comment Share on other sites More sharing options...
Totocellux Posted August 22, 2010 Share Posted August 22, 2010 complimenti, ti è capitato un ottimo esemplare di Q9650 e anche una ottima P5Q! Se sei alla ricerca non del massimo possibile ma di una conf stabile, equilibrata e con pochi consumi, essendo stabile a 3.6Ghz a 1.18V, quindi certamente sotto il VID standard, direi che lo puoi lasciare così. Controlla sempre che le temp non siano costantemente prossime ai 70°C. Comunque, imo, essendo i 450Mhz di Bus speed ampiamente alla portata della P5Q, è un peccato tenerla così: quella è una cpu da daily a [email protected], ampiamente in tranquillità (sempre controllando le temp, quindi probabilmente dovendo purtroppo cambiare dissi). Quote Link to comment Share on other sites More sharing options...
vjncenzo Posted August 22, 2010 Author Share Posted August 22, 2010 Grazie tom1. Poi controllo e vi faccio sapere. Ciao Totocellux. Il dissipatore che ho non è male ma quelle frequenze, come hai detto tu, lo dovrei cambiare e con esso anche il case perchè ho poco spazio. Per il momento tengo tutto così, più in la proverò ad aumentare anche perchè ho intenzione di cambiare cabinet. Quote Link to comment Share on other sites More sharing options...
tom1 Posted August 22, 2010 Share Posted August 22, 2010 Figurati di nulla se hai problemi posta pure Quote Link to comment Share on other sites More sharing options...
vjncenzo Posted August 22, 2010 Author Share Posted August 22, 2010 Ho fatto un ulteriore test con vcore a 1.18750 (1.176 full, 1.168 idle) e in 2 ore e 15 min non ha dato problemi. Avevo provato anche con vcore a 1.18125 ma purtroppo è crashato dopo 1 ora e 30 di test :grrr: tom1 purtroppo quel parametro non c'è nel bios Quote Link to comment Share on other sites More sharing options...
vjncenzo Posted August 23, 2010 Author Share Posted August 23, 2010 L'ho provato anche in idle e senza problemi. Lascio tutto così com'è. Grazie a tutti Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.