JD82 Posted January 17, 2008 Share Posted January 17, 2008 Salve, avrei bisogno di qualche consiglio su come far salire le RAM in oggetto. Attualmente le sto tenendo 2.12V/400/4-4-4-12 con impostazioni More Aggressive x3 / Fast x2 sul BIOS DFI. L'FSB è 333, non posso salire ulteriormente con il processore in firma. Everest segna Read: 7044 MB/s, Write: 6035 MB/s, Copy: 6599 MB/s e Latency: 68.9 ns. Ho provato a portarle a 533/5-5-5-15 con 2.3V ma non mi sono sembrate molto stabili. Stesso discorso per i 444/4-4-4-12. Vorrei sapere quanti volt massimi posso tenere in daily senza rischi e quali frequenze/timings mi consigliate, sempre per un uso daily ed una buona stabilità. Quote Link to comment Share on other sites More sharing options...
Febry Posted January 17, 2008 Share Posted January 17, 2008 dovrebbe esserci una recensione delle suddete nel portale... dacci un okkio!! :P se poi mi sbaglio ti diamo una mano "live" da qui! Quote Link to comment Share on other sites More sharing options...
valego Posted January 17, 2008 Share Posted January 17, 2008 Per il daily use non superare i 2,4v e magari tienile sempre ventilate, ti metto il link ad una discussione di nidecker dove le ha tirate un po' crucial ballistix pc6400 Valerio Quote Link to comment Share on other sites More sharing options...
JD82 Posted January 17, 2008 Author Share Posted January 17, 2008 ti metto il link ad una discussione di nidecker dove le ha tirate un po' crucial ballistix pc6400 dovrebbe esserci una recensione delle suddete nel portale... Grazie, la recensione l'ho vista, ma se non erro non si parla proprio di daily. A me interessava sapere che voltaggio massimo posso dare in sicurezza per un uso giornaliero. Comunque non andrò oltre i 2,4V... Grazie ancora Quote Link to comment Share on other sites More sharing options...
valego Posted January 17, 2008 Share Posted January 17, 2008 Con i 2,4v stai al sicuro, poi magari se hai dei chip fortunati riesci a dargli anche meno volt Valerio Quote Link to comment Share on other sites More sharing options...
JD82 Posted January 17, 2008 Author Share Posted January 17, 2008 Non so cosa sbaglio: 2.4V/500/4-4-4-12: il PC boota ma non riesce nemmeno ad avviarsi MemTest da penna USB. 2.4V/444/4-4-4-12: MemTest si avvia ma tira fuori migliaia di errori al test #5 dopo pochi minuti. Queste sono le tensioni e le temperature dopo 20 Min di Orthos (VDimm impostato a 2.19V): Potrebbe aiutare aumentare il voltaggio del NB? Lo tengo a default perché con i 333x9 mi basta. Potrebbe però giovare alle ram un po' di overvolt sull'X38? Quote Link to comment Share on other sites More sharing options...
valego Posted January 17, 2008 Share Posted January 17, 2008 Si alza anche il voltaggio del northbridge, magari a 1,45v tieni sempre un occhio alle temperature Valerio Quote Link to comment Share on other sites More sharing options...
JD82 Posted February 27, 2008 Author Share Posted February 27, 2008 Dopo i fallimenti dei post precedenti ho messo da parte per qualche tempo l'idea di occare le ram, ma nei giorni scorsi mi è tornata nuovamente la voglia, ed eccomi qui a chiedere aiuto. In particolare mi servirebbero cosigli sui settaggi avanzati presenti sul BIOS DFI (tWR, tWTR, tRRD, tRDWR, etc). Ci tengo a sottolineare che sono interessato esclusivamente a settaggi per uso daily, miro quindi ad ottenere una configurazione il più stabile e performante possibile. Ecco i miei settaggi daily: [font=Courier New][b]CPU Feature[/b] - Thermal Management Control: Enabled - PPM(EIST) Mode: Disabled - Limit CPUID MaxVal: Disabled - C1E Function: Disabled - Core Multi-Processing: Enabled Exist Setup Shutdown: Mode 2 Shutdown after AC Loss: Disabled CLOCK VC0 divider: AUTO CPU Clock Ratio: 9X - Target CPU Clock: 2997 MHz CPU Clock: 333 MHz Boot Up Clock: 200 DRAM Speed: 333/800 - Target DRAM Speed: DDR2 800 PCIE Clock: 101mhz PCIE Slot Config: 1X 1X CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled SATA Spread Spectrum: Disabled [b]Voltage Settings[/b] CPU VID Control: 1.41875V CPU VID Special Add: AUTO DRAM Voltage Control: 2.190V SB Core/CPU PLL Voltage: 1.640V NB Core Voltage: 1.405V CPU VTT Voltage: 1.355V Vcore Droop Control: Enabled Clockgen Voltage Control: 3.45v GTL+ Buffers Strength: Strong Host Slew Rate: Weak GTL REF Voltage Control: Disable x CPU GTL1/3 REF Volt: 110 x CPU GTL 0/2 REF Volt: 110 x North Bridge GTL REF Volt: 110 [b]DRAM Timing[/b] - Enhance Data transmitting: Fast - Enhance Addressing: Fast - T2 Dispatch: AUTO Clock Setting Fine Delay Ch1 Clock Crossing Setting: More Agressive - DIMM 1 Clock fine delay: Current 89ps - DIMM 2 Clock fine delay: Current 456ps - DIMM 1 Control fine delay: Current 534ps - DIMM 2 Control fine delay: Current 289ps - Ch 1 Command fine delay: Current 801ps Ch2 Clock Crossing Setting: More Agressive - DIMM 3 Clock fine delay: Current 89ps - DIMM 4 Clock fine delay: Current 400ps - DIMM 3 Control fine delay: Current 367ps - DIMM 4 Control fine delay: Current 356ps - Ch 2 Command fine delay: Current 801ps Ch1Ch2 CommonClock Setting: More Agressive Ch1 RDCAS GNT-Chip Delay: AUTO Ch1 WRCAS GNT-Chip Delay: AUTO Ch1 Command to CS Delay: AUTO Ch2 RDCAS GNT-Chip Delay: AUTO Ch2 WRCAS GNT-Chip Delay: AUTO Ch2 Command to CS Delay: AUTO (where cpuz sees 1T or 2T SETTING) CAS Latency Time (tCL): 4 RAS# to CAS# Delay (tRCD): 4 RAS# Precharge (tRP): 4 Precharge Delay (tRAS): 12 All Precharge to Act: AUTO REF to ACT Delay (tRFC): AUTO Performance LVL (Read Delay) (tRD): AUTO Read delay phase adjust: Enter Ch1 Read delay phase (4~0) - Channel 1 Phase 0 Pull-In: AUTO - Channel 1 Phase 1 Pull-In: AUTO - Channel 1 Phase 2 Pull-In: AUTO - Channel 1 Phase 3 Pull-In: AUTO - Channel 1 Phase 4 Pull-In: AUTO Ch2 Read delay phase (4~0) - Channel 2 Phase 0 Pull-In: AUTO - Channel 2 Phase 1 Pull-In: AUTO - Channel 2 Phase 2 Pull-In: AUTO - Channel 2 Phase 3 Pull-In: AUTO - Channel 2 Phase 4 Pull-In: AUTO MCH ODT Latency: AUTO Write to PRE Delay (tWR): AUTO Rank Write to Read (tWTR): AUTO ACT to ACT Delay (tRRD): AUTO Read to Write Delay (tRDWR): AUTO Ranks Write to Write (tWRWR): AUTO Ranks Read to Read (tRDRD): AUTO Ranks Write to Read (tWRRD): AUTO Read CAS# Precharge (tRTP): AUTO ALL PRE to Refresh: AUTO[/font] E qualche screenshot spero utile: Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.