Eduw2k Posted January 16, 2008 Share Posted January 16, 2008 dunque per questioni logistiche ho cambiato la p5wgd2 ws pro ed ho preso questa bella mainboard.. preso la cpu ben testata e messa su... nno capisco il perchè ma gia a 360 x 9 non e stabile.. consierando che questa bestiola regge i 425 x 9 ...... ora posto le impostazioni AI OVERCLOCK TUNER :MANUAL CPU RATIO SETTINGS : auto ( provato anche impostando 9) FSB Strap to north bridge : auto FSB FREQUENCY : 400 PCIE FREQUENCY : 100 DRAM FREQUENCY : 800 DRAM COMMAND RATE : auto Settaggi ram: ( le ho messe rilassate per provare ) Cas Latency :5 RAS to CAS delay : 5 RAS Precharge : 5 RAS ACTIVE TIME : 15 ( impostato fino a 17 ) Ras to RAS delay : 7 ROWRefresh Cycle Time : auto write recovery time : auto write to read delay : auto read to precharge time : auto DRAM static read control : auto AI clock Twister : Auto Transaction Booster : Disabled ( provato anche su auto ) Relax Level 1 Cpu voltage : 1.4375 (vdroppa un po il reale e 1.41 ) cpu pll voltage : auto fsb termination : auto dram voltage : auto ( provato nake su 2.1 ) North bridge : Auto South Bridge : auto Clock Over charging : auto cpu voltage dumper : Disabled CPU voltage preference : Auto North bridge Volt Preference : auto cpu/PCIE Spread Spectrum : Disabled nella parte cpu ho disabilitato il thermal control ecc.. unica nota il bios della MB è un beta 0503 rilasciato il 06/12/2007 le ram sono delle ocz 6400 platinium v2 4 4 4 15 alim tagan 800w u25 il raffreddamento è un d-tek fuzion con pompa swiftec 655 ( se non erro) e radiatore a 2 ventole ... si accettano suggerimenti Quote Link to comment Share on other sites More sharing options...
megthebest Posted January 16, 2008 Share Posted January 16, 2008 che dissy usi? le temperature come sono in full? che vid ha il quad? Quote Link to comment Share on other sites More sharing options...
Eduw2k Posted January 16, 2008 Author Share Posted January 16, 2008 il processore è questo http://www.xtremehardware.com/forum/f13/nuovo_q6600_l725b057-6432/ la temp stando al asusprobe in full load sui 44 quando parte il test prime95 ma dopo un 20 sec si stoppa impianto a liquido D-tek fuzion con relativa pompa swiftec la 655 se non erro .. il raffr ci sta tutto =) considera ke acvevo su il qx6700 a 370 x 10 è quello era un vero fornetto Quote Link to comment Share on other sites More sharing options...
Eduw2k Posted January 16, 2008 Author Share Posted January 16, 2008 nessuna ipotesi gente? Quote Link to comment Share on other sites More sharing options...
Eduw2k Posted January 20, 2008 Author Share Posted January 20, 2008 vabbe mi arrendo e pure uscito il bios non beta ma non regge .. bho... Quote Link to comment Share on other sites More sharing options...
Le085 Posted January 21, 2008 Share Posted January 21, 2008 tags =sclero vorrei vedere ..con quel che costa è proprio il colmo infatti...certo che ogni tanto asus sforna delle belle delusioni...:( Quote Link to comment Share on other sites More sharing options...
megthebest Posted January 21, 2008 Share Posted January 21, 2008 serve sicuramente un bios + maturo per questa mobo... è impossibile che non riesca in futuro a dare prova della sua bontà... non disperare e attendi altri bios.. ciao Quote Link to comment Share on other sites More sharing options...
dj883u2 Posted January 21, 2008 Share Posted January 21, 2008 C'è da dire che il chipset x38 è decisamente + difficule da gestire rispetto al P35. Quote Link to comment Share on other sites More sharing options...
Eduw2k Posted January 21, 2008 Author Share Posted January 21, 2008 400 x 9 stabile a 1.37v prime95 va in crash e anke occt ma non si e bloccato facendo 3dmark, encodando 2 divx e rendering... ne gioki vari ( ho vista 64 bit su..) sabato meto su xp Quote Link to comment Share on other sites More sharing options...
megthebest Posted January 21, 2008 Share Posted January 21, 2008 ma allora si clocca... non è che la cpu ha bisogno di 1,5v per stabilizzarsi a 3,6Ghz? Quote Link to comment Share on other sites More sharing options...
dj883u2 Posted January 22, 2008 Share Posted January 22, 2008 400 x 9 stabile a 1.37v prime95 va in crash e anke occt ma non si e bloccato facendo 3dmark, encodando 2 divx e rendering... ne gioki vari ( ho vista 64 bit su..) sabato meto su xp Metti su Windows xp.Windows vista non so neanche se supporta i due programmi in mamiera corretta. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.