Roll Mod'n 2012: ORGANIC II
-
Very nice!
-
seguo,bello davvero!
-
Thank you guys
But this is not everything made so far
Practically, I managed to give a proper shape to the case. Still a lot to sand, but roughly it is already in the target shape.
Now it's time to cover this ugly holes
Unfortunately I could not make desired shape without a form. Acrylic when heated is plastic too short. I've used a foam to create a forms. On the the foil I pour out foam. From the back it is protect by the plywood. I'm waiting until the foam expands itself and fill out the hole.
Then I can make plaster cast.
Now, either I use casting resin. Or gelcoat and laminate.
Meanwhile I'm still sanding.
-
Then I've modelled arm, at the end of which I will put hard drives. In my intention hard drive case will be in a disk shape, or even more like flower bud. Frankly a lot of work.
And now a small sample of the case along with the arm. There is obviously still missing an element containing the disks.
And after few days the arm is ready.
So it will look roughly like this. "Bud," of course, will also be trimmed.
Trimmed like this
-
Ok. I've finished the first stage of build. And now pictures with matrix and keyboard.
-
Now, I very briefly describe the methods that I used.
It is not an easy task. Because making a forms is very time consuming. It's even bigger waste of time to make a form, which will be used only once! But as it turned out not as difficult.
First, we need a positive element that will serve to do the form. In my case, these are elements made of the foam. To give them proper smoothness I've put putty layer. I used regular acrylic, because durability does not matter.
Light sanding and I've applied a layer of spray filler.
Now we have to sand it good. For each inequality at this stage will be reflected in the form.
At the end paint and a little polishing.
Now I've put some wax and do the form. In my case, it's single use of a form, so no point in doing it with resin. It was faster to make it from a building plaster. Just do not use other kind's of gypsum as I did before, because I had it in my hand. It was a total failure. That was the reason why I had to finish all "caps" with a putty. Building plaster dries much faster and is hard.
After removing the positive element the form is ready. Small form problems I fill and sand.
It is time to use a gelcoat. I give a very thick layer. In some places above the centimeter, because then there is no problem with sanding and polishing.
After removing the element looks like this:
And after grinding so:
Later I will show photos after polishing, because at the moment I do not have the right polish paste.
The advantage of this method is that the resin is very hard and not easy to scratch. And even if it does it's the whole element stays in one colour.
And here is one more "plug".
Model made ??of foam and over treated.
The form just before flooding with gelcoat.
And laminate after removing from the form.
The same element during processing.
Still a little work on polishing and it will be finally ready.
As you can see I've at once flooded with gelcoat power and lan sockets. In this module I should be able to put power supplies and access point.
Flooding the power and LAN nests in the resin prompted me with the idea for the implementation of my communication LEDs.
I've decided to flood a piece of plexiglass in another module.
Then I sanded it a little.
And try it in place.
As you can see now, there are noticeable scratches and visible place of connection. But to sand it finally and polish it I have to wait . Because as I found out, gelcoat final hardness is achieved only after several hours. Probably this is my error resulting from inadequate amounts of hardener.
-
Small session with an already made elements
I've changed the method of making the mold. So far I've been using foam and putty and then sanding it.
And now I've tested method of making the mold from modeling clay.
As you can see by the mold, this method also works.
It gives huge advantage in time. Instead of hours or days, the execution takes tens of minutes. Next week, all the elements made of the resin should be ready.
-
After a long brake I've made some inlay on the hdd arm. Grinding itself is not complicated. The problem was to find right putty in a black colour. In the end I got the best results using epoxy putty.
Some progress. One side of the case is almost finished. Unfortunately, routing channels and filling it with putty is quite slow.
This is almost finished case.
Then ......
After some discussion with friends I had to redesign the case. The new version of the arm is mounted on the back and on the opposite side. Now I think there is better balance between front and rear, and right or left side.
-
Working in wood is almost finished. Just take some time to painting and final polishing. So I had a moment to complete the first illumination element in the resin. I think the best will be a "little touch" of light. I do not want to get a Christmas tree.
I'm curious of your opinion:)
And there are two pictures from the side I previously had mounted the arm.
And for now it's everything. As you can see this project is in very advanced stage. But it took me more then half a year to get this result. Now I will place here next updates.
I am very curious of your opinion.
-
hard work, but beautiful effect, never seen such a thing
-
wow!!!!!!
davvero interessante e ambizioso come progetto....
-
Thank you very much guys. All of you for your support
I've mounted all resin elements in to the both sides of the case. I also did much of the back-light. Probably I will mount some kind of regulator to take control of light intensity. It will be easier to adjust the power.
Probably I will leave the keyboard painted in black. Because polished keys are not giving the desired effect.
-
Love it.
-
wow, excellent work... pure craftsmanship... absolutely beautiful!!!
-
:D:D:D:clapclap:Awesome -
looooooool impressive
-
Awesome i dont see
-
[FASE 2: Preparazione alla votazione] 15 Giugno - 22 Giugno
A fine concorso ogni utente avrà una settimana di tempo per presentare le foto o i video finali del proprio progetto per le votazioni, ogni utente potrà postare un massimo di 4 foto e 2 video per mod, tali foto rappresenteranno l'ultimo post del worklog e saranno quindi seguite dai ringraziamenti agli sponsor in caso di sponsorizzazione.
[Phase 2: Preparing to vote] June 15th to June 22nd
At the end of the contest each user will have a week to present the photos or videos of his final project to the vote, users can post up to 4 photos and 2 videos for each mod, these photos represent the last post of the worklog and then will be followed by thanks to the sponsors in the event of sponsorship.
-
Ciao! Sembra che tu sia interessato a questa conversazione, ma non hai ancora un account.
Stanco di dover scorrere gli stessi post a ogni visita? Quando registri un account, tornerai sempre esattamente dove eri rimasto e potrai scegliere di essere avvisato delle nuove risposte (tramite email o notifica push). Potrai anche salvare segnalibri e votare i post per mostrare il tuo apprezzamento agli altri membri della comunità.
Con il tuo contributo, questo post potrebbe essere ancora migliore 💗
Registrati Accedi