Mod in a Week // "APASF: CP London Edition" (Update: 1st Day Completed)
-
Subscribed.
-
Cheers guys! It´s good to be back
---------------------
Tuesday: Day 2 of 7
Most of today´s avaliable time I dedicated to pretty much sanding the case down. Normally on a new case that hasn´t got a glossy finish I wouldn´t bother to much about this but since a large portion of the case imitates copper in this design it needs to be as smooth as possible so this was needed. That however is boring so I´m going to show you the rest of what I did today.
I finished yesterday´s side panel (for now, still missing the window and a couple of details), as in, added the final lighter coats of the ageing process and attached the brass details to which I had also aplied the ageing.
Once that was fully dry I put it away safely for now (can´t afford any accidents!).
After all that (very) tedious sanding, cleaned it all up and aplied a good coat of primer to both the top section and the chasis.
Oh and, I fixed the damage caused by the shipping of the case! I like to think it came out quite well, time constraints and all considered.
And for the last 2 hours of today´s avaliable time, I aplied a few coats of the copper. It´s amazing how many more coats the chasis needs in comparison to the plastic bits, I actually ran out of paint, so, need to get some more tomorrow!
It goes without saying that the copper will be aged as well, can´t have none of that new shinyness here!
And that´s it for the second of 7 days in this Mod in a Week project, I hope you keep on reading tomorrow, now I need a shower, get something to eat and go to my "other" job
-
very good! i'll keep in touch!
-
Subscribed
-
nice and classic color
-
Thanks guys, hope you´re enjoying the worklog!
-----------------
Wednesday: Day 3 of 7
Today was a late start. I got home from work at around 5am last night and between having something to eat, shower, etc I didn´t get to sleep till 6am. Obviously when my alarm was set to wake me up at 10am so I could continue with the project it was a bit of a "no f**ing way* so kept on sleeping for a couple of extra hours.
That said I think I´m doing good in terms of progress. So today I started with some of the bits and bobs, like the XSPC reservoir / D5 pump combo.
I aplied the vinyl...
...and did my thing
So, on the top of the case there´s a hotswap/dock bay that I´d though I´d give the treatment (mostly because I don´t want copper to be everywhere without wooden bits here and there).
I still have to aply the ageing process to the brass detail but, I quite like it!
Oh, I did go and buy extra copper paint, and the chasis took a grand total of 7 coats (7 COATS!!) to get a solid color on...
This is a bit of a drawback though as because of the amount of coats, it is going to take longer to be ready for matt lacquer which then has to dry itself (though that only takes about an hour) which means I can´t play with the barebone chassis till at least late tomorrow or even friday. Thankfully however there´s not much that needs to do be done to that, so really as long as that part is ready by the time I´m ready to put all the hardware in, it shouldn´t be an issue.
I also did some work on the frontal CM logo. Not sure if it´s obvious in the photos but I did slightly overlap the letter borders in order to exagerate them so they look "curvier", not sure if that makes sense? Also, as you will see, my "fix" didn´t hold
I can´t say I´m surprised, the amount of epoxy left on it after sanding was minimal in order to keep the shape, so I´m thinking some superglue and of course the preassure of the bay components will keep it in place.
Oh and here´s something really special...
...and...
So yes, so far I think it´s been the most fun day of the 3 so far for me, though my hands are full of inks of several tones which are extremely hard to get rid off!
And well, that´s it for the third of the seven days of this Mod in a Week, as always I hope you´re enjoying keeping track of it and hope you come back for more tomorrow!
-
well done
-
Amazing!!!!
I like how it is coming
-
Lamptron FC10
-
an artist
-
Thanks for the support guys!
(
-----------------
Thursday: Day 4 of 7
Had a bit of a misshap today and took a ton of process photos, once finished I realised there memory card wasn´t in the camara...
...so all photos are actually from the end of today but I´ll explain what I did aniway
My sister gave me a hand today with her epic caligraphy skills and finally paid tribute to the name.
Tomorrow we will do a few other writings under that and I can consider that sidepanel (aside from the window and its details) finished.
The other side panel however was finished today.
Remember yesterday I did the CM logo on the front? Well this is what it was in preparation for...
Did the wood detail on the usb and audio connections up top.
And finally I couldn´t resist putting it all togueter to see how it was going, have in mind there´s still a LOT to do in terms of detailing the case and effects but... I was shocked... just...wow. I´m in love! Also, you´ll notice there´s something different about the copper. I used a sponge to aply a darker tone of copper (though with a pearl effect) so the copper changes tones depending on the light as you can see by the pictures).
Well, that´s it for the fourth of the 7 days. The idea for tomorrow is to finish with the external look of the case. Do that DVD drive that will go in that open slot in the front and work on the hardware!
I´ve hoped you´ve enjoyed today´s update and that you come back for more tomorrow!
-
Very nice!
-
Friday: Day 5 of 7
Bunch of problems today. Unfortunately neither the ASUS motherboard nor the CM PSU made it in time so I´m having to use alternative parts. Gigabyte had sponsored a motherboard for a different project so I contacted them and ask them if it´d be ok for me to use it with this project, they said sure so I went ahead with it and well, it seems to go hand in hand...
However I´m most likely going to have to shave off the mobo´s heatsink as it´s just a bit to tall to allow the rad to fit in the case. I do have a slimline rad which fits just fine but it seems to be leaking so I can´t trust it.
The PSU is more of a decision than an issue, I´ve got a brand new Corsair TX650 but I´m thinking it´s going to cut it short for a GTX560 Ti SLI setup, while I do have an NZXT HALE90 (850w) it´s going to be a pain as that´s within my main PC so it means taking the whole thing apart to get it out. So I decided for now to go with the Corsair, took it apart, and started to paint it.
Also started customizing the EK 360 rad.
So I´m going to take the chance to say thanks as all these products where either sponsored or winnings from previous project.
First of all, massive thanks to Gigabyte, I could have been in serious trouble if it wasn´t for you guys!
Thanks Corsair for the TX650!
Thanks Mayhems for the coolant!
a Special mention for Kingston. 2x 240Gb HyperX SSDs + 16Gb 1866Mhz DDR HyperX ram!
Thanks to Lamptron for the FC10!
So. I´ve now done all I can do before sticking all the HW in, so that´s what I´m doing on Day 6 and hell, if possible even finish this project on day 6, so you know, I can sleep on Sunday (that´d be nice).
Thanks for reading!
-
amzing work luciel
-
Saturday: Day 6 of 7
Though technically today is Sunday, I couldnt post yesterdays update as I had to source some parts from my everyday pc so I had no PC to post from.
I will reply to all comments on Monday evening when I´m setup at the Campus Party event (hopefully everything arrives in one piece, gulp.
Right so, more issues. The radiator was stuffed, leaking and while fixable I didn´t have the time and I had to bring my PC to the workshop aniway so figured I´d just use its rad instead. So, sourced the radiator from the main pc, cpu, ram and harddrives and the build went on, luckily from here on, only small fixable-on-the-spot issues where encounted.
Let the cabeling and tinkering begin!
Gave the final coat of copper to the PSU and lackered afterwards.
In it goes along with the rest of the parts.
Fingers crossed for a problem-free boot...
Success!!!! It even recognised my raid array from my previous setup (different mobo)! All hdds, ssds and devices detected.
And that´s it for day 6, join me on the final day!
-
Sunday: Day 7 of 7
Final day!
As I mentioned in the previous entry I will reply to all comments on Monday evening if all arrives ok.
Today I finished it all up. There will be a second set of pictures from the CP event but here´s the first set. It goes without saying had it not been a time limited edition, I would´ve done a lot more detailing and precision work but, well all things considered and a few faults aside, I´m really glad on how it turned out.
So, I give you, Mod in a Week: "APASF: CP London Edition".
With special thanks to:
And that´s the end of the project. I hope you have enjoyed following it. I will post an updated as mentioned tomorrow (Monday) evening if all arrives well.
Now, to bed!
-
Awesome work, mate!
But I would suggest adding copper tubes for the liquid circuit! That would be even more awesome!
-
epic build
-
Thanks a bunch guys. Yes I used copper pipes on the original APASF, unfortunately it takes to much time and that´s why I didnt do it this time round
FINAL PICTURES SET 2 - Campus Party Europe London O2 Arena:
While I´m waiting for a bunch of people to email me photos, here´s a selection of what I currently have, you´ll even recognise the original APASF on the screen as I was talking about sponsorships and how it affects companies in terms of publicity, value for money, etc. You may also recognise a certain Hans (pOpE) and Anthony Leather (Combatus) who where fantastic to meet in person! All in all I think it´s safe to say we all had a blast at the event!
As a side note, updated first post and added all current final pictures to the "reserved for final pictures" part.
Ciao! Sembra che tu sia interessato a questa conversazione, ma non hai ancora un account.
Stanco di dover scorrere gli stessi post a ogni visita? Quando registri un account, tornerai sempre esattamente dove eri rimasto e potrai scegliere di essere avvisato delle nuove risposte (tramite email o notifica push). Potrai anche salvare segnalibri e votare i post per mostrare il tuo apprezzamento agli altri membri della comunità.
Con il tuo contributo, questo post potrebbe essere ancora migliore 💗
Registrati Accedi