[Thread Ufficiale] EVGA X58 SLI Classified
-
THREAD UFFICIALE
EVGA X58 SLI CLASSIFIED
Specification and Performance Performance
Based on Intel X58/ICH10R chipset Supports Intel Core i7 Processors 133 Mhz QPI Memory
6 x 240-pin DIMM sockets Triple Channel DDR3 Maximum of 24GB of DDR3 1600MHz+Expansion Slot
4 x PCIe x16/x8, 1 x PCIe x1 1 x 32-bit PCI, support for PCI 2.1Storage I/O
1 x UltraDMA133 9 x Serial ATA 300MB/sec with support for RAID 0, RAID1, RAID 0+1, RAID5, JBODIntegrated Peripherals
8 Channel High Definition 2 x 10/100/1000Multi I/O
1 x PS2 Keyboard 12 x USB2.0 ports (8 external + 4 internal headers) Audio connector (Line-in, Line-out, MIC) FireWire 1394A (1 external, 1 header)Form Factor
EATX Form Factor Length: 12in – 304.8mm Width: 10.375in – 263.5mmNotes:
The ULTIMATE in X58 motherboards is here! The EVGA X58 Classified raises the bar for enthusiast grade motherboards everywhere.
With never before seen features such as 3-way SLI + PhysX + 1x PCIe device on a single board, 2 8pin +12V connectors capable of delivering 600 watts of power, 10 phase Digital PWM with a switching frequency of up to 1333KHz, three times the amount of normal gold content in the CPU socket and much, much more.
The EVGA X58 Classified motherboard is engineered for those who demand more than just the best!
EVGA Support Manual for EVGA X58 Classified E759/E760/E761Download PDF Spec Sheet 141-BL-E760-A1 -
THREAD UFFICIALE
EVGA X58 SLI CLASSIFIED
Specification and Performance Performance
Based on Intel X58/ICH10R chipset Supports Intel Core i7 Processors 133 Mhz QPI Memory
6 x 240-pin DIMM sockets Triple Channel DDR3 Maximum of 24GB of DDR3 1600MHz+Expansion Slot
4 x PCIe x16/x8, 1 x PCIe x1 1 x 32-bit PCI, support for PCI 2.1Storage I/O
1 x UltraDMA133 9 x Serial ATA 300MB/sec with support for RAID 0, RAID1, RAID 0+1, RAID5, JBODIntegrated Peripherals
8 Channel High Definition 2 x 10/100/1000Multi I/O
1 x PS2 Keyboard 12 x USB2.0 ports (8 external + 4 internal headers) Audio connector (Line-in, Line-out, MIC) FireWire 1394A (1 external, 1 header)Form Factor
EATX Form Factor Length: 12in – 304.8mm Width: 10.375in – 263.5mmNotes:
The ULTIMATE in X58 motherboards is here! The EVGA X58 Classified raises the bar for enthusiast grade motherboards everywhere.
With never before seen features such as 3-way SLI + PhysX + 1x PCIe device on a single board, 2 8pin +12V connectors capable of delivering 600 watts of power, 10 phase Digital PWM with a switching frequency of up to 1333KHz, three times the amount of normal gold content in the CPU socket and much, much more.
The EVGA X58 Classified motherboard is engineered for those who demand more than just the best!
EVGA Support Manual for EVGA X58 Classified E759/E760/E761Download PDF Spec Sheet 141-BL-E760-A1 -
INSTRUCTIONS: BIOS updating can be accomplished VIA one of the below methods:
CD Method (Blank CD and CD Rewritable Drive Required) - Download the following .iso file: E760_S61J.iso .
- Use CD Burning software to burn the .iso image onto a blank CD (Nero, Alochol 120%, MagicISO etc.).
- After it has burned, insert CD and restart the machine, go into the BIOS and load defaults, save and exit.
- Now set the CD Drive as the primary boot device, or press escape while the system is booting to select CD as the bootable device.
- After flash remove the CD, and power off PC Completely.
- Turn on the PC and load defaults in BIOS
USB FLOPPY (Floppy Disk and Disk Drive Required)- Download the following executable: E760_S61J.exe .
- Insert blank floppy disk into drive and run executable.
- Now set the USB Floppy as the primary boot device, or press escape while the system is booting to select USB Floppy as the bootable device.
- After flash remove the floppy, power off PC Completely.
- Turn on the PC and load defaults in BIOS.
USB Flash Drive Installation Download E760S61J.bin.
Visit this thread and follow the installation instructions.
Rendere Bootable la Pendrive USB:
Scaricare l'HP Usb Storage Format Tool v2.1.8 free download e Win98boot.zip
Scompattate il .rar dov'è contenuta l'Utility HP e installatela..
Una volta installata cliccate con il tasto destro e aprite come amministratore.
Ora scompattate anche l'archivio di destinazione "win98boot" e incollatelo sul desktop (lo potete incollare dove volete non è importante).
Torniamo al programmino HP, mettete la spunta su: "Quick Format", "Create a DOS startup disk" e "using DOS system files located at:".
Ora gli dovete far vedere la cartella di destinazione : "win98boot".
Come compare questo messaggio date la conferma.
Ora la vostra chiavetta USB è pronta all'uso
Se volete flashare il bios inserite nella pendrive l'AWDFLASH e il BIOS.bin. e via con lo shut down..
Cosa importantissima.. mi raccomando prima del flash fate un cmos !!!!
Ora dopo il cmos avviate il pc e premete "esc".. ora vi trovate davanti ad una schermata nera con delle scritte che termina in "C:/", ora subito dopo scrivete : AWDFLASH (spazio) NOMEBIOS.bin (es: AWDFLASH E760S61J.bin), vi chiederà se volete salvare il vecchio bios, confermate e aspettate che il flash sia andato a buon fine..
Premete F1 per riavviare..
Buon divertimento
Database BIOS :
74 Updates:- Corrects 15x uncore multi shown as 16x in BIOS with Intel 980X
73 Updates: - Added TRL setting to assist with memory compatibility while overclocking
64 Updates:- Adds 1.5x uncore support for B1 CPU
- Adds number of GPUs detected at bootup
- Adds RC/AC setting in memory timings
59 Updates:- Removes shutdown action when enabling Virtualization Technology
- Sets ICH Voltage to 1.1v as Default
49 Updates:- Removes shutdown action when enabling Virtualization Technology
- Sets ICH Voltage to 1.1v as Default
44 Updates:- Supports 32nm Desktop CPUs
- Added "Turbo Performance" option (may boost performance if enabled)
- Fixes 1866MHz Memory Ratio
S61J Updates:- Added "Reserve RC for Bridge" - Enables resources for 5 VGA's
- Added High Precision Event Timer
- Disables PS2 keyboard in device manager if no PS2 keyboard present
S61H Updates:- Adds support for 2TB Partitions (DATA)
S61D Updates:- Increased Shadow Memory in DOS for PXE
- Improved USB Support
S61B Updates:- Restores Bootup Logo
- Maximum Payload for PCIE
- SMART Fan Temperatures from 0 to 100c
S61A Updates:- Improves Bootup BClock
- Adds B2B CAS Delay
S618 Beta Updates:- Updates smart fan function between low and high threshold
- Increase high temp threshold lower limit for smartfan
- Improves bootup BCLCK
- Turbo mode bug fixed
- USB option display issue corrected
- Changes default clockgen PCIe mode
S615 Beta Updates:- Smartfan is listed by temp they are adjusted to
- PXE fix with RAID enabled
- Improves bootup BCLK
- Improves 24GB support
- Smartfan improvements
S610 Updates:- Improves support for Intel Xeon CPU's
- Fixes Smart Fan S3 Resume
- Adds additional option for QPI Signal
- S3 Resume Improvements
- Corrects 15x uncore multi shown as 16x in BIOS with Intel 980X
-
Molti di voi avranno notato che al primo avvio il Display Code della mobo (E760) non rimane fisso su FF...
Se anche voi avete questo "problema" basta che disabilitate la voce "P80 Show CPU Temp" (grazie a dj883u2 per la dritta
)Consiglio su come impostare il Bios (nel mio caso con il Raid0):
Advanced Bios Features:
- Hard Disk boot Priority> 1.SCSI-0 : Intel Volume0 (RAID Mode)
- First boot Device : Hard Disk
- Second boot Device : Disabled
- Third boot Device : Disabled
- Boot other device : Enabled
- Boot Up Numlock Status : ON
- Security Option : Setup
- Full Screen Logo Show : Enabled/Disabled
Integrated Peripherals:
- Onboard PATA/SATA Device: > RAID (RAID Mode)
- JMB 362 SATA Controller : Disabled
- JMB 363 SATA/PATA Controller : Disabled
- JMB 363 Mode : Raid (RAID Mode)
- JMB 362 Mode : Raid (RAID Mode)
Onboard Device:
Realtek GigaLan 1: Disabled/Enabled
Realtek GigaLan 2: Disabled/Enabled
PE4 Slot: Disabled
Realtek Lan PXE Boot Rom: Disabled
TI 1394 Setting: Disabled
High Definition Audio: Enabled
P80 Show CPU temp: Disabled
Power Management Setup:
- ACPI Function : enabled
- ACPI Sospend Type : S1 (POS)
- Soft-Off by PWP-BTTN : Instant Off
- Wake-Up by PCI Card : Enabled
- Resume Alarm : Disabled
- Power On Function : Disabled
- PWRON After PWR-Fail : Off
PnP/PCI Configurations:
- Init Display First : PCI-E
- Reset Configuration Data : Disabled
- Resources Controlled by : Disabled
- PCI/VGA Palette Snoop : Disabled
- INT Pin 1/8 Assignment : Auto
- MAXIMUM PAYload Size : 128
INTRODUZIONE OVERCLOCK
BIOS: E760S61J
RS @__191x21__
Core i7 920 D0
gskill Trident 1600MHz Cas 6
BIOS TEMPLATE
Frequency/Voltage Control
- DUMMY OC : Disabled
- Extreme Cooling : Disabled
- CPU Clock Ratio : 20x (21x Turbo ON)
- CPU Host Frequency (MHz) : 191
- MCH STRAP : Auto
- CPU UnCore Frequency : 3061 (MHz) 16x
- CPU Clock Skew : 0 ps
- Spread Spectrum : Disabled
- PCIE Frequency (MHz) : 101 MHz
- OC Recovery : Disabled
CPU Feature
- Intel Speed Step : Disabled
- Turbo Mode Function : Enabled
- CxE Function : Disabled
- Execute Disabled Bit : Disabled
- Virtualization Technology : Disabled
Logical Processor Setting
- Intel HD Technology : Enabled
- Active Processor Core : ALL
QPI Controller Setting
- QPI Controll Setting : Enabled
- QPI Link Fast Mode : Enabled
- QPI Frequency Selection : 4.800GT/s
Memory Feature
- Memory SPD : Standard 1
- Memory Control Setting : Enabled
- Memory Frequency : 2:8 - 1530Mhz
- Channel Interleave Setting : 6 way
- Rank Interleave Setting : 4 way
- Memory low gap : 2,5GB
Voltage Control
- EVGA VDrop Control : without VDroop
- CPU Vcore : 1.20625v (Dipende dalla vostra CPU)
- CPU VTT Voltage : +75mv (+100mv)
- CPU PLL Vcore : 1.800v
- IOH PLL Vcore : 1.800v (1.820v)
- QPI PLL Vcore : 1.300v
- DIMM Voltage : 1.610v (1.650)
- DIMM DQ VREF : +0mv
- IOH Vcore : 1.200v
- IOH/ICH I/0 Voltage : 1.550v
- ICH Vcore : 1.050v
- VTT PWM Frequency : 370KHz
- CPU PWM Frequency : 940KHz
- CPU Impedance : Less
- QPI Signal Compensation : Less
-
BIOS: E760S61J
RS @__201x21__
Core i7 920 D0
gskill Trident 1600MHz Cas 6
BIOS TEMPLATE
Frequency/Voltage Control
- DUMMY OC : Disabled
- Extreme Cooling : Disabled
- CPU Clock Ratio : 20x (21x Turbo ON)
- CPU Host Frequency (MHz) : 201
- MCH STRAP : Auto
- CPU UnCore Frequency : 3221 (MHz) 16x
- CPU Clock Skew : 0 ps
- Spread Spectrum : Disabled
- PCIE Frequency (MHz) : 101 MHz
- OC Recovery : Disabled
CPU Feature
- Intel Speed Step : Disabled
- Turbo Mode Function : Enabled
- CxE Function : Disabled
- Execute Disabled Bit : Disabled
- Virtualization Technology : Disabled
Logical Processor Setting
- Intel HD Technology : Enabled
- Active Processor Core : ALL
QPI Controller Setting
- QPI Controll Setting : Enabled
- QPI Link Fast Mode : Enabled
- QPI Frequency Selection : 4.800GT/s
Memory Feature
- Memory SPD : Standard 1
- Memory Control Setting : Enabled
- Memory Frequency : 2:8 - 1604Mhz
- Channel Interleave Setting : 6 way
- Rank Interleave Setting : 4 way
- Memory low gap : 2,5GB
Voltage Control
- EVGA VDrop Control : without VDroop
- CPU Vcore : 1.26875v (Dipende dalla vostra CPU)
- CPU VTT Voltage : +100mv
- CPU PLL Vcore : 1.800v
- IOH PLL Vcore : 1.800v (1.820v)
- QPI PLL Vcore : 1.300v
- DIMM Voltage : 1.650v
- DIMM DQ VREF : +0mv
- IOH Vcore : 1.200v
- IOH/ICH I/0 Voltage : 1.550v
- ICH Vcore : 1.050v
- VTT PWM Frequency : 370KHz
- CPU PWM Frequency : 940KHz
- CPU Impedance : Less
- QPI Signal Compensation : Less
BIOS: E760S61J
TEST @__221x21__
Core i7 920 D0
gskill Trident 1600MHz Cas 6
BIOS TEMPLATE
Frequency/Voltage Control
- DUMMY OC : Disabled
- Extreme Cooling : Disabled
- CPU Clock Ratio : 20x (21x Turbo ON)
- CPU Host Frequency (MHz) : 221
- MCH STRAP : Auto
- CPU UnCore Frequency : 3541 (MHz) 16x
- CPU Clock Skew : 0 ps
- Spread Spectrum : Disabled
- PCIE Frequency (MHz) : 101 MHz
- OC Recovery : Disabled
CPU Feature
- Intel Speed Step : Disabled
- Turbo Mode Function : Enabled
- CxE Function : Disabled
- Execute Disabled Bit : Disabled
- Virtualization Technology : Disabled
Logical Processor Setting
- Intel HD Technology : Enabled
- Active Processor Core : ALL
QPI Controller Setting
- QPI Controll Setting : Enabled
- QPI Link Fast Mode : Enabled
- QPI Frequency Selection : 4.800GT/s
Memory Feature
- Memory SPD : Standard 1
- Memory Control Setting : Enabled
- Memory Frequency : 2:8 - 1770 MHz
- Channel Interleave Setting : 6 way
- Rank Interleave Setting : 4 way
- Memory low gap : 2,5GB
Voltage Control
- EVGA VDrop Control : without VDroop
- CPU Vcore : 1.38750v
- CPU VTT Voltage : +200mv
- CPU PLL Vcore : 1.800v
- IOH PLL Vcore : 1.800v
- QPI PLL Vcore : 1.400v
- DIMM Voltage : 1.700v
- DIMM DQ VREF : +0mv
- IOH Vcore : 1.300v
- IOH/ICH I/0 Voltage : 1.650v
- ICH Vcore : 1.050v
- VTT PWM Frequency : 490KHz
- CPU PWM Frequency : 1210KHz
- CPU Impedance : Less
- QPI Signal Compensation : Less
Se il mio sistema è stabile non è detto che lo sia anche il vostro.. allego questa guida affinchè riusciate ad individuare il problema dei famosi BSOD
DIAGNOSI ERRORI BSODs
BSOD "IRQL_NOT_LESS_THAN_OR_EQUAL" (Conflitto hardware)
BSOD 101 "Clock Interrupt not received from Secondary Processor" Provare ad aumentare il VCore
BSOD 124 "general hardware failure" Provare ad aumentare il VTT
Attempted Write To Readonly Memory (stop code 0X000000BE)
Bad Pool Caller (stop code 0X000000C2)
Data Bus Error (stop code 0X0000002E)
Driver IRQL Not Less Or Equal (stop code 0X000000D1)
Driver Power State Failure (stop code 0X0000009F)
Driver Unloaded Without Cancelling Pending Operations (stop code 0X000000CE)
Driver Used Excessive PTEs (stop code 0X000000D8)
Hardware Interrupt Storm (stop code 0X000000F2)
Inaccessible Boot Device (stop code 0X0000007B)
Kernel Data Inpage Error (stop code 0X0000007A)
Kernel Stack Inpage Error (stop code 0X00000077)
Kmode Exception Not Handled (stop code 0X0000001E)
Mismatched Hal (stop code 0X00000079)
No More System PTEs (stop code 0X0000003F)
NTFS File System (stop code 0X00000024)
Page Fault In Nonpaged Area (stop code 0X00000050)
Status Image Checksum Mismatch (stop code 0Xc0000221)
Status System Process Terminated (stop code 0Xc000021A)
Thread Stuck In Device Driver (stop code 0X000000EA)
Unexpected Kernel Mode Trap (stop code 0X0000007F)
Unmountable Boot Volume (stop code 0X000000ED)
BSOD 101 "Clock Interrupt not received from Secondary Processor" Di solito basta Aumentare il VCore
BSOD 124 "general hardware failure" Provate ad aumentare il VTT
NB: Se in OC Windows vi da l'errore Kernel-Processor-Power (Event 35):
Performance power management features on processor 1 in group 0 are disabled due to a firmware problem. Check with the computer manufacturer for updated firmware.
Provate ad abilitare l'Intel Speed Step !
Capita anche di avete strani riavvii, bsod, ecc (o comunque degli errori inerenti al firmware..).
Se avete dei dubbi potete controllare gli errori andando su "Run" (Esegui/Start+R), eventvwr.
-
Reserved
-
bel thread... ottimo lavoro
-
ottimo lavoro Gabriellì...
-
iscritto:clapclap:
-
Veramente ottimo!
Scheda madre stupenda....da smanettoni intenditori!:clapclap:
-
Grazie a tutti
-
Ho "scoperto" (dopo svariati bsod) che windows 7 ultimate 64 non digerisce l'Intel Speed Step disabilitato (almeno su questa mobo)
Abilitandolo non compare più nessun errore "Kernel-Processor-Power" ecc..
Potete controllare se avete gli stessi errori andando su "Run" (Esegui/Start+R), eventvwr
Cmq aggiungo in prima pagina
-
G-UNIT91 ha scritto:
iscritto:clapclap:te vedi di non far danni...
come andiamo con la classy???
-
delly ha scritto:
te vedi di non far danni...
come andiamo con la classy???
sto smadonnando con il backup per poi fare il multi..per adesso tutto a posto!:clapclap: sembra strano eh?
-
già...strano davvero...
-
DC2 ha scritto:
Ho "scoperto" (dopo svariati bsod) che windows 7 ultimate 64 non digerisce l'Intel Speed Step disabilitato (almeno su questa mobo)Abilitandolo non compare più nessun errore "Kernel-Processor-Power" ecc..
Potete controllare se avete gli stessi errori andando su "Run" (Esegui/Start+R), eventvwr
avevi anche il CxE disabilitato?
E' probabile che il problema comunque sparirà con ulteriori release di Bios
-
Totocellux ha scritto:
avevi anche il CxE disabilitato?E' probabile che il problema comunque sparirà con ulteriori release di Bios
Si il CxE sempre disabilitato.. ho dovuto abilitare lo Speed Step dalla disperazione.. bsod x3,14
Speriamo.. cmq sono ritornato al vecchio S610 perchè (almeno secondo me) va meglio
-
DC2 ha scritto:
Si il CxE sempre disabilitato.. ho dovuto abilitare lo Speed Step dalla disperazione.. bsod x3,14Speriamo.. cmq sono ritornato al vecchio S610 perchè (almeno secondo me) va meglio
Per la Classified 760 prova il Bios Ver S61J:
ftp://ftp.evga.com/bios/E760S61J.bin
Ne parlano tutti molto bene!
-
dj883u2 ha scritto:
Per la Classified 760 prova il Bios Ver S61J:ftp://ftp.evga.com/bios/E760S61J.bin
Ne parlano tutti molto bene!
quoto, questo ho flashato:n2mu:
-
dj883u2 ha scritto:
Per la Classified 760 prova il Bios Ver S61J:ftp://ftp.evga.com/bios/E760S61J.bin
Ne parlano tutti molto bene!
Si, fino a due giorni fa ho avuto l'S61J (lo si vede anche dai test in prima pag.).. il bello è che ho trovato 2 appunti sulla scrivania e con quello vecchio ero stabile con un filo di vcore in meno..
Visto che non ho notato altre differenze ho rimesso quello vecchio (S610).. aspetto una nuova release e la provo
G-UNIT91 ha scritto:
quoto, questo ho flashato:n2mu:Ce l'hai fatta a flasharlo finalmente
..come ti ci trovi ? Ps. anche te hai Win 7 64 ultimate giusto ? Hai notato problemi con lo Speed Step disabilitato ?
Ciao! Sembra che tu sia interessato a questa conversazione, ma non hai ancora un account.
Stanco di dover scorrere gli stessi post a ogni visita? Quando registri un account, tornerai sempre esattamente dove eri rimasto e potrai scegliere di essere avvisato delle nuove risposte (tramite email o notifica push). Potrai anche salvare segnalibri e votare i post per mostrare il tuo apprezzamento agli altri membri della comunità.
Con il tuo contributo, questo post potrebbe essere ancora migliore 💗
Registrati Accedi