g1lgamesh

thanks for making me feel welcome:)

cheers fella!

No mate I cannot as I work for Lamptron. Maurizio (Oneros) and I are work colleagues and it would be a conflict of interest. I will post my other build soon. The theme on the other mod is that I like Ancient Sumerian history and as such I read and write cuneiform fluently. As a result i made a build called 'Sumerian Cry' (which is on the BIT-TECH forums) I will post that here soon. However there is no harm in doing what you can not for the sake of a contest, but the sake of community spirit:)

Additional Rules Like KustomPCS on facebook Kustom PCs - Impresa locale - Ayr | Facebook Like Lamptron UK on facebook Accedi | Facebook Remember EU and UK entrants ONLY! All mods posts must be made in this thread ***EDIT im deciding the place winners on this one, So a handy hint is......... I am looking for originnality as mods based on games BORE me! TO post YOUR MOD entry please visit MOD THE FAN CONTROLLER Contest - Kustom PC's Forums

more tomorrow drive bay will be ready

cheers fella:)

First of all First Side panel completed Please note all photos are taken before the final clear protective layer has been added, the reason for that is that I allow a MONTH to cure! Side panel outside Side Panel inside. Ok next The only spare NEW spacing style rad i have right now is an Old Black Ice GT Stealth. UV BLUE at that =yuucccccccccck. Obviously the colour doesnt go with the builds...... So after some painting and yes i had to paint the fins:( Due to paint type it wont effect the performance very much it now looks like this: The build is REALLY starting to come along now:)

Front Panel outside After de-greasing and priming (as shown earlier) To get this look, I used 'Polar White' then masked the first 8.5cm off the bottom as this will be for the red colour. The red used is a Metallic Hycote 'Tango RED' which goes fairly well with the off-white, but it is still a little harsh even though its a lot more classy than what I call 'Slapper' Red. To balance it out a little i sprayed a fine mist of crystal silver so it appears there are clouds within the red. As you can see there is still a small issue to fix on the bottom right near the colour line. The inside was essentially the same as above, however gloss white was used instead.

Redid mother board tray. I cannot alter the slight messup I did with the LED holes, however at least I can repaint the aforementioned tray. This now marries with the PCIE backing plate. This is before the clear protective layer has been added.

Finished cross struts Polar white on the outside and gloss white on the inside:0 Backing plate m/b tray area Nice smooth job even if I have to say so myself:D

Some more shots of the same plate but on differing light conditions. next the cross struts After the usual sanding, de-greasing and primer etc Finally I used Polar white on the outside And gloss white on the inside. this is the first coat only. note i havent coated this side of the ends really. The reason for this is that all this has to be assembled again:) Plus this side of the ending section is never seen as it slots into the front and back panels

next we have the back panel Before sanding and de-greasing After two coats of primer and a good sanding down

First of all made a bit of a mess drilling these holes. These are for the LED's the will be mounted near the edge I never realised how thin the aluminium was, well at least the LED's are going underneath the motherboard in order to create a nice backlit effect.

PCIE Section. FOr this I used two coats of primer, two coats of Hycote Tango Red (Metallic) and a coat of crystal silver (same company) FOr this I didnt just wish for a candy effect, one wanted a kind of a cloud/mixed colour painting Anyway I applied the crystal silver coating whilst the tango red was still wet in order to achieve this effect. this is before the clear protective coating has been applied.

FRONT panel sanded down, just before washing after washing, two coats of primer and then sanded down with 600 grit paper.